Mitsubishi (Japan) S2001 toughening agent plastics modified PC toughened weather resistant resistant 寒丽 cationic MBS S-2001 - Products

Product Details

Basic Parameters

Japan

Mitsubishi (Japan) S2001 toughening agent plastics modified PC toughened weather resistant 耐寒丽阳MBS S-2001

📖 product introduction

Mitsubishi (Japan) S2001 toughening agent plastics modified PC toughened weather resistant 耐寒丽阳MBS S-2001。属PC、 compatibilizer material material ， suitable for 耐寒、 toughened 、 modified 等领域。 in stock 供应， quality assured 。

⚙️ processing 参数参考

processing temperature 范围

270-310°C

mold temperature

70-100°C

drying conditions

120°C / 3-4h

干燥 time

0.02%

molding shrinkage 0.5-0.8%

📋 详细 technology 信息

Mitsubishi S系产品应用.jpg

📋 认证 and 合规信息

🧪 化学耐受 performance

优异 ✅稀酸矿物油醇类(短期)盐溶液脂肪烃

good 好 ✔植物油洗涤 agent臭氧

受限 ⚠酮类芳香烃halogen 代烃ester 类强碱

避免 ❌丙酮二氯甲烷氯仿氢氧化钠浓液

🌟 material material 优势

PC（ polycarbonate (PC) ） is transparent degree 最高 engineering plastics 之一(透光率88-91%)，同时具 has extreme 高 impact resistant 强 degree (缺口 impact 800+J/m)。PC广泛 used for 安全眼镜、车灯、 electronic housings 、建筑采光板等领域， is "以塑代玻" 核心 material material 。

📦 储存 and 处理建议

PC resin moisture absorption property 强，必须储存 in 干燥、密封环境 in 。 processing 前120°C干燥3-4小时(除湿干燥机)，含水率控制 in 0.02%以下。含水率过高会严重影响制品 performance (水解降解、银纹、 bubbles)。PC pellets 开封后应尽快使用。

🌍

RoHS 合规

符合欧盟RoHS指令

🏭

ISO 认证

质量管理体系

✅

quality assured

原厂正品

更多 engineering plastics Model 请访问daoqinsh.com

📐 详细物 property 参数表

测试项目	典 type 值	测试标准	单位
density	1.18-1.22	ASTM D792	g/cm³
melt flow index (MFR)	3-65	ASTM D1238	g/10min
玻璃化转变 temperature (Tg)	145-150	ASTM D3418	°C
透光率(3.2mm)	88-91	ASTM D1003	%
雾 degree (3.2mm)	0.7-1.0	ASTM D1003	%
tensile strength (屈服)	60-70	ASTM D638	MPa
断裂伸长率	100-150	ASTM D638	%
flexural modulus	2300-2400	ASTM D790	MPa
flexural strength	90-100	ASTM D790	MPa
悬臂梁缺口 impact (23°C)	800-900	ASTM D256	J/m
悬臂梁缺口 impact (-30°C)	600-700	ASTM D256	J/m
洛氏 hardness	M70 / R125	ASTM D785	—
heat deflection temperature (HDT) (0.45MPa)	130-140	ASTM D648	°C
heat deflection temperature (HDT) (1.8MPa)	125-135	ASTM D648	°C
line property thermal expansion coefficient	60-70	ASTM D696	10⁻⁶/°C
体积电阻率	>10¹⁵	ASTM D257	Ω·cm
介电强 degree	15-20	ASTM D149	kV/mm
介电常数(1MHz)	2.9-3.0	ASTM D150	—
water absorption (24h)	0.15-0.35	ASTM D570	%
molding shrinkage	0.5-0.8	ASTM D955	%
UL94 flame retardant rating	V-2 (1.5mm)	UL 94	—
extreme 限氧指数(LOI)	25-27	ASTM D2863	%

* 以上数据 is 典 type 参考值，具体以原厂TDS is 准

If you have any questions about Mitsubishi (Japan) S2001 toughening agent plastics modified PC toughened weather resistant resistant 寒丽 cationic MBS S-2001, or would like to request Mitsubishi (Japan) S2001 toughening agent plastics modified PC toughened weather resistant resistant 寒丽 cationic MBS S-2001 datasheet, MSDS, ROHS test report, SGS report, REACH certificate, FDA certificate, EU regulation certificate, UL certificate, or COC/COA report, please call our service hotline +86-192-7986-4570, or click Contact Us to leave us a message.

Product Features

Mitsubishi (Japan) S2001 toughening agent plastics modified PC toughened weather resistant resistant 寒丽 cationic MBS S-2001 Properties, Mitsubishi (Japan) S2001 toughening agent plastics modified PC toughened weather resistant resistant 寒丽 cationic MBS S-2001 Product Parameters, Mitsubishi (Japan) S2001 toughening agent plastics modified PC toughened weather resistant resistant 寒丽 cationic MBS S-2001 Performance Data, Mitsubishi (Japan) S2001 toughening agent plastics modified PC toughened weather resistant resistant 寒丽 cationic MBS S-2001 Factory Report, MSDS, Material Safety Data Sheet, UL Yellow Card, SGS Report, RoHS, Food Grade Certification, NSF Drinking Water Standard, Product Information, Product Performance, Factory Report, Original Packaging, Authorized Distributor, Heat Deflection Temperature, Melt Index, Flow Coefficient, Impact Resistance, Impact Strength, Low Temperature Toughness, Low Temperature Impact Resistance, Melt Flow Rate, Processing Technology, Processing Parameters, Processing Temperature, EU RoHS, German FDA, US FDA, Japan FDA