HDPE in stock 独山子石化 DMDA-8008H injection molding bottle cover material high density polyethylene (PE) raw materials - Products

Product Details

Basic Parameters

ENGINEERING PLASTICS

HDPE in stock 独山子石化 DMDA-8008H injection molding 瓶盖 material high density polyethylene (PE) raw materials

📖 product introduction

HDPE in stock 独山子石化 DMDA-8008H injection molding 瓶盖 material high density polyethylene (PE) raw materials 。属PE material material ， suitable for injection molding 等领域。 in stock 供应， quality assured 。

⚙️ processing 参数参考

processing temperature 范围

180-250°C

mold temperature

30-60°C

drying conditions

70°C / 2h

干燥 time

0.01%

📋 详细 technology 信息

undefined

📋 认证 and 合规信息

🧪 化学耐受 performance

优异 ✅稀酸/稀碱醇类盐溶液洗涤液food contact 介质

good 好 ✔植物油矿物油(短期)

受限 ⚠芳香烃halogen 代烃氧化 property 酸

避免 ❌浓硝酸发烟硫酸

🌟 material material 优势

HDPE（ high density polyethylene (PE) ）具 has high crystallinity 、 high strength 、 high rigidity and 优 good chemical resistant 品 property 。HDPE广泛 used for in 空容器、 pipe/tube 、 film 、 injection molding 制品等领域， is 替代金属管道理想 material material 。其 good 好 processing property and 低成本使其 in packaging 、建筑、农业等行业具 has 不可替代地位。

📦 储存 and 处理建议

HDPE pellets 应储存 in 干燥阴凉处，避免阳光直射。 moisture absorption property extreme 低，一般不需干燥。 processing 前70°C干燥2小时可去除表面水分。远离火源 and 强氧化 agent 。密封 packaging 可保存2年以上。

🌍

RoHS 合规

符合欧盟RoHS指令

🏭

ISO 认证

质量管理体系

✅

quality assured

原厂正品

更多 engineering plastics Model 请访问daoqinsh.com

📐 详细物 property 参数表

测试项目	典 type 值	测试标准	单位
density	0.940-0.970	ASTM D792	g/cm³
melt flow index (MFR)	0.05-30	ASTM D1238	g/10min
melt temperature	130-137	ASTM D3418	°C
tensile strength (屈服)	22-35	ASTM D638	MPa
断裂伸长率	100-600	ASTM D638	%
flexural modulus	800-1500	ASTM D790	MPa
悬臂梁缺口 impact	30-100	ASTM D256	J/m
邵氏 hardness	D55-D65	ASTM D2240	—
heat deflection temperature (HDT) (0.45MPa)	75-90	ASTM D648	°C
维卡软化点	115-125	ASTM D1525	°C
line property thermal expansion coefficient	100-200	ASTM D696	10⁻⁶/°C
体积电阻率	>10¹⁶	ASTM D257	Ω·cm
介电强 degree	20-50	ASTM D149	kV/mm
water absorption (24h)	<0.01	ASTM D570	%
molding shrinkage	1.5-3.0	ASTM D955	%
UL94 flame retardant rating	HB	UL 94	—
extreme 限氧指数(LOI)	17-18	ASTM D2863	%
ESCR(F50)	>50	ASTM D1693	h

* 以上数据 is 典 type 参考值，具体以原厂TDS is 准

If you have any questions about HDPE in stock 独山子石化 DMDA-8008H injection molding bottle cover material high density polyethylene (PE) raw materials, or would like to request HDPE in stock 独山子石化 DMDA-8008H injection molding bottle cover material high density polyethylene (PE) raw materials datasheet, MSDS, ROHS test report, SGS report, REACH certificate, FDA certificate, EU regulation certificate, UL certificate, or COC/COA report, please call our service hotline +86-192-7986-4570, or click Contact Us to leave us a message.

Product Features

HDPE in stock 独山子石化 DMDA-8008H injection molding bottle cover material high density polyethylene (PE) raw materials Properties, HDPE in stock 独山子石化 DMDA-8008H injection molding bottle cover material high density polyethylene (PE) raw materials Product Parameters, HDPE in stock 独山子石化 DMDA-8008H injection molding bottle cover material high density polyethylene (PE) raw materials Performance Data, HDPE in stock 独山子石化 DMDA-8008H injection molding bottle cover material high density polyethylene (PE) raw materials Factory Report, MSDS, Material Safety Data Sheet, UL Yellow Card, SGS Report, RoHS, Food Grade Certification, NSF Drinking Water Standard, Product Information, Product Performance, Factory Report, Original Packaging, Authorized Distributor, Heat Deflection Temperature, Melt Index, Flow Coefficient, Impact Resistance, Impact Strength, Low Temperature Toughness, Low Temperature Impact Resistance, Melt Flow Rate, Processing Technology, Processing Parameters, Processing Temperature, EU RoHS, German FDA, US FDA, Japan FDA