POM KEP (Korea) F10-03H LOF polyoxymethylene (POM) pellets low odor low 释放甲 aldehyde pom plastics - Products

Product Details

Basic Parameters

Korea

POM KEP (Korea) F10-03H LOF polyoxymethylene (POM) pellets 低气味低释放甲醛pom plastics

POM

📖 product introduction

POM KEP (Korea) F10-03H LOF polyoxymethylene (POM) pellets 低气味低释放甲醛pom plastics 。属PO、POM material material 。 in stock 供应， quality assured 。

⚙️ processing 参数参考

processing temperature 范围

190-230°C

mold temperature

60-100°C

drying conditions

80°C / 3h

干燥 time

0.02%

molding shrinkage 1.5-2.5%

📋 详细 technology 信息

undefined

📋 认证 and 合规信息

🧪 化学耐受 performance

优异 ✅矿物油/ lubricated 脂燃 material 油醇类弱碱醚类

good 好 ✔稀释 has 机酸液压油醛类(短期)

受限 ⚠强酸强碱酚类酮类(部分)

避免 ❌浓盐酸浓硫酸甲酸氧化 property 酸

🌟 material material 优势

POM（ polyoxymethylene (POM) ）被誉 is " ultra- 钢"， is engineering plastics in friction coefficient 最低、 wear resistance 最好品种之一。POM具 has high rigidity 、高尺寸精 degree and 自 lubricated property ，广泛 used for 精密 gears 、 bearings 、拉链、 automotive parts 等， is 替代金属理想 material material 。

📦 储存 and 处理建议

POM pellets 必须储存 in 干燥、密封环境 in 。POM对热敏感，储存 temperature 不宜 ultra- 过50°C。 processing 前80°C干燥3小时，含水率控制 in 0.1%以下。远离酸类化学品(酸蒸汽会导致POM解聚)。密封 packaging 保质期1-2年。

🌍

RoHS 合规

符合欧盟RoHS指令

🏭

ISO 认证

质量管理体系

✅

quality assured

原厂正品

更多 engineering plastics Model 请访问daoqinsh.com

📐 详细物 property 参数表

测试项目	典 type 值	测试标准	单位
density	1.40-1.43	ASTM D792	g/cm³
melt flow index (MFR)	2-30	ASTM D1238	g/10min
melt temperature	165-178	ASTM D3418	°C
tensile strength (屈服)	60-70	ASTM D638	MPa
断裂伸长率	20-75	ASTM D638	%
flexural modulus	2600-3100	ASTM D790	MPa
flexural strength	85-98	ASTM D790	MPa
悬臂梁缺口 impact (23°C)	60-120	ASTM D256	J/m
洛氏 hardness	M80-M94 / R120	ASTM D785	—
heat deflection temperature (HDT) (1.8MPa)	100-125	ASTM D648	°C
维卡软化点	160-168	ASTM D1525	°C
line property thermal expansion coefficient	80-120	ASTM D696	10⁻⁶/°C
体积电阻率	>10¹³	ASTM D257	Ω·cm
介电强 degree	15-20	ASTM D149	kV/mm
friction coefficient (对钢)	0.1-0.3	ASTM D1894	—
磨耗量(Taber,1000g)	10-20	ASTM D1044	mg
water absorption (24h)	0.20-0.25	ASTM D570	%
molding shrinkage	1.5-2.5	ASTM D955	%
UL94 flame retardant rating	HB	UL 94	—

* 以上数据 is 典 type 参考值，具体以原厂TDS is 准

If you have any questions about POM KEP (Korea) F10-03H LOF polyoxymethylene (POM) pellets low odor low 释放甲 aldehyde pom plastics, or would like to request POM KEP (Korea) F10-03H LOF polyoxymethylene (POM) pellets low odor low 释放甲 aldehyde pom plastics datasheet, MSDS, ROHS test report, SGS report, REACH certificate, FDA certificate, EU regulation certificate, UL certificate, or COC/COA report, please call our service hotline +86-192-7986-4570, or click Contact Us to leave us a message.

Product Features

POM KEP (Korea) F10-03H LOF polyoxymethylene (POM) pellets low odor low 释放甲 aldehyde pom plastics Properties, POM KEP (Korea) F10-03H LOF polyoxymethylene (POM) pellets low odor low 释放甲 aldehyde pom plastics Product Parameters, POM KEP (Korea) F10-03H LOF polyoxymethylene (POM) pellets low odor low 释放甲 aldehyde pom plastics Performance Data, POM KEP (Korea) F10-03H LOF polyoxymethylene (POM) pellets low odor low 释放甲 aldehyde pom plastics Factory Report, MSDS, Material Safety Data Sheet, UL Yellow Card, SGS Report, RoHS, Food Grade Certification, NSF Drinking Water Standard, Product Information, Product Performance, Factory Report, Original Packaging, Authorized Distributor, Heat Deflection Temperature, Melt Index, Flow Coefficient, Impact Resistance, Impact Strength, Low Temperature Toughness, Low Temperature Impact Resistance, Melt Flow Rate, Processing Technology, Processing Parameters, Processing Temperature, EU RoHS, German FDA, US FDA, Japan FDA