Product Details

Basic Parameters

ExxonMobil Santoprene 191-85PA

ExxonMobil · Santoprene · TPV · nylon 粘合 grade TPV

density (g/cm³)

0.950

hardness (Shore)

89A

product features

nylon (PA)粘合 property

chemical resistance

高 hardness

包覆 molding

application areas

PA包覆 moldingindustrial componentsautomotive parts

product introduction

ExxonMobil Santoprene（山都平） is 全球领先热塑 property 硫化 elastomer (TPV) Brand ，由EPDM/PP动态硫化制得，兼具橡胶优异弹 property and 热塑 property plastics 可 processing property ， widely used in 汽车密封、建筑防水、电子电气 and 医疗等领域。

⚙️ injection molding processing 参数参考

melt temperature 范围

250-290°C

mold temperature

60-90°C

drying conditions

80°C / 4h

injection pressure

80-130 MPa

molding shrinkage

0.7-2.0%

processing 备注

moisture absorption property 强，必须充分干燥

🧪 化学耐受 performance

优异 ✅矿物油/ lubricated 脂燃 material 油液压油醇类

good 好 ✔弱碱洗涤 agent醚类

受限 ⚠强酸酚类甲酸浓碱

避免 ❌浓硫酸浓盐酸甲酸(溶解)

🌟 material material 优势

nylon (PA) is 应用最广泛 engineering plastics 家族，具 has high strength 、 high toughness 、 wear resistant 自 lubricated 、耐油等优异 features 。不同品种(PA6/PA66/PA12等)可满足从 general purpose 到高 heat resistant 各种需求。

📋 认证 and 合规信息

🌍

RoHS 合规

符合欧盟RoHS指令

🏭

ISO 认证

质量管理体系认证

✅

REACH

欧盟化学品合规

💧

quality assured

原厂正品保障

📦 储存 and 处理建议

nylon 类 resin 均 has 较强 moisture absorption property ，必须储存 in 干燥密封环境 in 。 processing 前80°C干燥4小时以上(除湿干燥机推荐)。开封后尽快使用，含水率控制 in 0.1%以下。

产地

USA /新加坡

processing method

extrusion / injection molding / blow molding

material 筒 temperature

180-230°C

干燥要求

一般无需干燥（8200系列等非 moisture absorption grade 可直接 processing ）

daoqinsh.com · Daoqin plastics · ExxonMobil ExxonMobil 专业供应商

📐 详细物 property 参数表

测试项目	典 type 值	测试标准	单位
density	1.12-1.15	ASTM D792	g/cm³
melt flow index (MFR)	5-80	ASTM D1238	g/10min
melt temperature	215-225	ASTM D3418	°C
tensile strength (干态)	60-85	ASTM D638	MPa
tensile strength (调湿态)	45-60	ASTM D638	MPa
断裂伸长率(干态)	50-300	ASTM D638	%
flexural modulus (干态)	2500-3000	ASTM D790	MPa
flexural strength (干态)	85-120	ASTM D790	MPa
悬臂梁缺口 impact (干态)	50-150	ASTM D256	J/m
洛氏 hardness	R118-R122	ASTM D785	—
heat deflection temperature (HDT) (0.45MPa)	180-210	ASTM D648	°C
heat deflection temperature (HDT) (1.8MPa)	65-80	ASTM D648	°C
line property thermal expansion coefficient	60-80	ASTM D696	10⁻⁶/°C
体积电阻率	>10¹²	ASTM D257	Ω·cm
介电强 degree	15-25	ASTM D149	kV/mm
friction 系数	0.15-0.35	ASTM D1894	—
water absorption (24h/饱 and)	1.8/3.0	ASTM D570	%
molding shrinkage	0.7-1.5	ASTM D955	%
UL94 flame retardant rating	V-2	UL 94	—

* 以上数据 is 典 type 参考值，具体以原厂TDS is 准

If you have any questions about ExxonMobil Santoprene 191-85PA TPV nylon bonding grade, or would like to request ExxonMobil Santoprene 191-85PA TPV nylon bonding grade datasheet, MSDS, ROHS test report, SGS report, REACH certificate, FDA certificate, EU regulation certificate, UL certificate, or COC/COA report, please call our service hotline +86-192-7986-4570, or click Contact Us to leave us a message.

Product Features

ExxonMobil Santoprene 191-85PA TPV nylon bonding grade Properties, ExxonMobil Santoprene 191-85PA TPV nylon bonding grade Product Parameters, ExxonMobil Santoprene 191-85PA TPV nylon bonding grade Performance Data, ExxonMobil Santoprene 191-85PA TPV nylon bonding grade Factory Report, MSDS, Material Safety Data Sheet, UL Yellow Card, SGS Report, RoHS, Food Grade Certification, NSF Drinking Water Standard, Product Information, Product Performance, Factory Report, Original Packaging, Authorized Distributor, Heat Deflection Temperature, Melt Index, Flow Coefficient, Impact Resistance, Impact Strength, Low Temperature Toughness, Low Temperature Impact Resistance, Melt Flow Rate, Processing Technology, Processing Parameters, Processing Temperature, EU RoHS, German FDA, US FDA, Japan FDA