Shanghai Daoqin Plastics Co., Ltd.

        一, injection molding workshop safety production 通则:

        1, equipment positive 常运转时, remove injection molding machine front safety 门, control sheet/plate outer, 严禁接触 equipment 任何部位.

        2, production 异常 处理必 must and other in equipment 停止运转 rear can 进行.

        3, equipment must 建立专人 negative made (定人定 mechanism), equipment safety training, 并经取 操 as 资格, 不 操 as equipment; fault/failure repair workshop 指定人员进行, non 指定人员不 进行 repair as.

        4, as positive as, 精心维护 equipment, maintain as ring 境整洁, good production.

        5, 严格执行 process and as 纪律, good 各项记录, 交接班必 must safety 情况.

        6, type equipment safety anti plant/unit must full, has loss bad, must and 时报修, 待修复 rear can use.

        7, positive analysis, and various 事故苗头, 事故消灭 in 萌芽状态. 如发生事故, need 果断, positive 确处理, and 时如实 toward upper grade report, 并保护现场, good detailed 记录.

        8, upper must 按规定 装, long need 扎起, 不准披发, 不准穿背心, short or 裙子, 不准穿拖鞋.

        9, use power tools front must electrical 线, 插头, plastics outer housing/shell has loss.

        10, more gas 接头时关闭 gas 源, anti 止接头飞出伤人.

        11, 维持通道畅通, in inner long time as or 堆放工 parts.

        12, equipment use 完毕必 must electrical 源, injection molding machine PC material temperature outer.

        二, injection molding machine safety production must 知:

        1, injection molding machine semi positive production 时, has lower as can 进行:

        a.打开 front safety 门

        b.取出 product and material 杆

        c.关闭 front safety 门

        如 need outer as, must technology 员确认 positive production must as, can as 业.

        2, remove outer 任何动 as, must in 手动状态 lower, 关停油泵 rear 进行;涉 and electrical, also must electrical 源, ratio as can can 接触射嘴 and 熔胶筒时, must electrical 源, safety, 清理工模 or adjustment machine parts front, must electrical 源;

        3, equipment 自动报警时, as 业人员必 must from equipment scope/range inner 撤出, to “手动”状态.

        4, 发生紧急事 parts (人身事故, equipment, mold 突然发出异常响声)时, 立即按 lower 紧急停止按钮, large 声求援.

        5, machine 运转时, will 身体任何部位伸入关闭 safety inner; 手伸入 mold front will safety 门打开;检查, 修理时如 upper semi 身进入两模 sheet/plate in 间, 应关掉油泵;无论 what combined, 整 身体进入两模 sheet/plate 时都应先切断 electrical 源.

        6, machine 运转时, must rear safety 门, must use front safety control mold 开锁模.

        7, machine 运转时. remove injection molding machine as outer 任何人接触 injection molding machine front, must notice injection molding machine as to 手动状态, 关停油泵. especially is more 人协同 as 业时, 任一方 has 异常动 as front, must notice 协同人员, to rear can as 业.

        a. injection molding machine as is as injection molding machine production, debugging 人, can can is 挡车工, 顶岗人员, can can is debugging 人员.

        b.异常动 as: remove strip/profile 款列出 动 as outer as.

        8, separation in 手动, semi 自动状态 lower, 检查拉开 safety can 否切断油泵 and electrical 源.

        9, 检查紧急停止按钮 is has 效, lower can 否切断油泵 and electrical 源.

        10, ensure equipment and equipment 周围无油, water, 保障行走 safety.

        11, injection molding machine 异常情况(漏油, electrical loss bad, electrical appliances loss bad and other and other) and toward long or technology report.

        12, remove nozzle must anti measures, high temperature raw materials, gas 体飞溅烫伤.

        13, retardant material or material 斗时, 请勿操 as machine.

        14, for injection 时, front rear safety 门, and 任何人不 站 in material 筒两侧, is material injection shot loss 伤遗憾终身.

        15, machine long use rear again machine, must safety plant/unit (如 machine 械锁, safety 门行程开关 and liquid pressure and other) positive rear can 运行该 equipment.

        16, as 业时, 切断主 electrical 源, upper “ prohibited electrical ”牌, front, machine 械按规定连接.

        17, 当射台 toward front 移动时, can use 手 清 remove from 射嘴漏出 熔胶, 以免伤手.

        18, material 斗里必 must has magnetic force 架, anti mixed metal material loss bad injection molding equipment.

        19, 检查, 修理时如 upper semi 身进入两模 sheet/plate in 间, 应关掉油泵.

        20, what combined, 整 身体进入两模 sheet/plate 时都应先切断 electrical 源.

        21, safety equipment 改动都 is 不允许, safety plant/unit loss bad lower 不 开动 equipment production.

        22, production high temperature product (mold temperature high 于120 degree)必 must use thick 棉布手 sleeve/set.

        三, 模, temperature machine safety production must 知:

        1, electrical must use electrical pressure (220V/380V/415V/50/60Hz).

        2, use 状态不明 thermally conductive 油.

        3, electrical 源线必 must use specifications product, anti formed hot, electrical pressure decline, 发生事故 or fault/failure.

        4, 请务必 will machine 接 端子 and 接 线 versus 连接.

        5, used for plant/unit has soft tube/pipe and other plant/unit, must need heat resistant 120℃, resistant pressure 1000kpa(10kgf/cm 2).

        6, soft tube/pipe 安装请 according to soft tube/pipe manufacturing 商 指示进行. especially attention/notes need for most small bending semi 径. soft tube/pipe 连接, 请参照 附录 soft tube/pipe tube/pipe need 领书.

        7, due to machine (包括 external 接续 阀门 type and tube/pipe type)运转时会 generate high temperature, need use 手 触摸. another, rear due to hot still has high temperature. in machine and tube/pipe temperature degree decline to 40℃ below/following, need 触摸.

        8, need use wet 手触摸 control 箱, can can 会引起触 electrical 事故.

        9, in repair as 业时, anti use product.

        10, has 异常发生, in parts has more front, need use plant/unit.

        11, 请定期 more thermally conductive 油, 当发现 thermally conductive 油呈黑绸状时请务必 more 换.

        12, use in 如发现排 water or cooling 效果差, 请立即清洗 electrical magnetic or cold water 出入口 has retardant 塞.

        四, machine safety production must 知:

        1, machine in injection molding machine upper 安装牢 solid.

        2, as 人员不 进入 machine 械手臂 as scope/range.

        3, repair front 请关掉 electrical 源.

        五, safety production must 知:

        1, in machine 周围1米 inner 不 放置 easy material product.

        2, setting temperature degree need raw materials drying temperature degree, combined experience setting.

        3, high temperature, must belt/tape anti use product, anti 止烫伤.

        4, dispersion 落烘箱 inner raw materials, must and remove.

        5, 清理, 修理烘箱时, must electrical 源.

        6, 每2 small 时检查1次烘箱 is positive 常运转, temperature degree.

        六, powder machine safety production must 知:

        1, in machine front ensure material and 网架关闭, safety filament must 拧紧.

        2, 转动刀 sheet/slice 极锋利且 can 引起伤害, especially is in 转动时.

        3, in material 斗网架时, easy 发生事故.

        4, machine electrical box/case high pressure 危险.

        5, machine is 由传动 belt/tape 传动, need let belt/tape to 衣服, 身体.

        6, in machine repair maintenance 时, must 关闭主开关 and control 开关, and other sheet/slice 静止不动.

        7, need anti plant/unit.

        8, if material powder in also has by powder material material, can machine, is heavy machine 时, material formed 马达 载.

        七, safety production must 知:

        1, electrical mono heavy machine (俗称行车) must 由专人操 as, as must training combined rear can upper as.

        2, front 应进行试车, is in 无载荷 情况 lower, 检查各运转 machine 构, control system and safety plant/unit is 否灵敏, 准确, safety can 靠;检查吊钩, is solid, appearance loss.

        3, electrical mono heavy machine in 起吊工 parts 时, parts weight in 吊钩, and electrical mono heavy machine scope/range inner.

        4, 不 沿主梁 direction 斜吊工 parts.

        5, in has 火灾危险, 爆炸危险 介质 in as and use 吊运熔化 metal and has 毒, easy easy material product.

        6, 吊装工 parts process in, parts 以稍离 面 is 宜.

        7, electrical mono heavy machine in 吊运工 parts process in, parts lower 面严禁站人.

        8, will parts rear, as 人员离开操 as 现场, 行车无人 tube/pipe made.

        9, as 完毕, electrical mono heavy machine in 规定位置, rise 起吊钩, electrical 源.